Posted on Dec 19, PM. Yes, I am testing all morning. The update fixes most of the issues I knew that three different computers can't have the same problem. Automatic file sharing works via Ethernet. I tried the following setups:. Posted on Feb 12, AM. Hi Steffen, hats off to you for gathering this valuable information! I'm going to title this post:. A quick look at those logs of yours.. Simply the Bonjour service is having a hard time trying to find you and also qmaster been running ragged trying to mount your Cluster 21DF0-BF7EC storage.
Try this and start from beginning. Do your best to perform these work instructions. Try also not to deviate if u can.
Check the activity monitor and confirm there are no compressord sub tasks running. Qmasterd might be running. That's ok. Step 2: set up your dedicated network for your transcoding cluster.. In this step you will isolate your cluster network to a dedicated subnet. For this procedure will make an IP address range 1. Step 3: mount all filesystems over the Ethernet 1. Simplicity is important at this stage to make sure you know what being accessed.
This is one reason for disabling all the automatic compressor settings. These can be saved as favourites in the " Connect to Server " dialogues.
Do the same for where the final distribution transcode is to be written with you user access.. Do these for all your slave macs. Remember you are specifying file paths over the 1.
Obviously make sure your slaves have read and write access. Yes and you could also mark these folders and Shared in Finder info then everyone can see them C verify your access: on each slave use the finder to create a ftest older in those recently mounted volumes. Delete the test folder. I for one rather like the new compressor. Qmaster is buried and works well when not teased or unintentionally fooled.
Jan 23, AM. I could not alter my last passage because the Apple forum suddenly presented the "Back soon" yellow postit. The suggestion by Apple works! Running the distributed job from an external volume works. Now we have to find out why it does not from an internal one. Jan 29, PM. Page content loaded. Thanks for the question. I found information relevant to your question in the Compressor User Guide.
You may find the information helpful:. Compressor User Guide. Dec 21, AM. Dec 21, AM in response to matt00 In response to matt Thank you both for the replies.
I already read those information. As I wrote, the shared computers are displayed in the preferences and can be selected. When a job is started, the master computer tries to distribute its footage but the connected slave doesn't do anything.
It doesn't get the chunks of the material. It seems it can't get proper access to the shared volume. Nothing helps. I never got a distributed transcoding work. Wait — no, it worked only one time approx. The slave got the work pieces for a short time and stopped after doing a bit of transcoding. It never ever worked again since then.
Dec 21 Friedward. Server has re-enabled them. Dec 21 Friedward kernel[0]: nfs connect socket error 61 for Dec 21 Friedward com. SharingHelper[] : Exited: Killed: 9. It doesn't matter which codec I try to transcode. I used diverent: mpeg4, ProRes, h. When I use a custom folder, Compressor on the slave can't access the footage. It is the same behavior on three different computers. Dec 21, PM. Of course it is enabled. I even mounted the specific storage folders on the other Mac.
The only volume I can't see from the other side is that temporary Shared volume. May this be the reason? I cannot believe that three different computers have the same problem. Does it work with your computers?
Can you write a detailed step-by-step instruction here, please? Jan 21, AM. Apple Support wrote that they never had this issue before. There are hardly any errors in the logs. This is what I found. Jan 22, PM. Wow, what a novel! But thank you very much for writing this long and very detailed step by step instruction. To cut a long story short.
It worked only once. I did every single step. As expected, the crux was the mounting of the network volumes. Mounting with "s teffen 1. I instead added the Storage folders and the source and destination folders manually in the Shared preference pane of Mac OS X and mounted the folders with "s teffen 1.
Up came a dialog where I could select all four shared folders. The job was done successfully. I tried another job with the same settings. The master Mac created 4 segments and worked one after another for itself. There was no distribution to the slave Mac anymore.
I did the whole setup procedure again with no success. I deleted the folders, made many restarts. The slave Mac again gives the error message in the Network Encoder Monitor that it could not find the source file.
I am so tired of this Compressor clustering thing. Jan 23, PM. Hi Steffen, well it's better having a deal of detail than advice that's based on the drone of "removing prefs" and "repairing disk permissions" based on some but not all "folk lore" and perhaps myths!
To your latest effort. It certainly looks like you had some pleasure with this, although it was brief. I am certain that this latest issue is simply related to the ACCESS and the availability of the objects resources you need for your transcoding transactions. It certainly does not hurt anything if you add this structure with the correct access and permissions. Yes, then there is certainly an access issue here that's likley very very easy to fix. In the log above you can see can see the successful access of the host.
In you case, I'd be certain there was an error in eht slave for this. I use shared dedicated directories for the client jobs I do. This way I have everything accessible from each host. I also use destination templates which is a huge workflow help. I believe Apple's intention was to make it very very easy to use. They have done a good job so far with compressor. I think the available Compressor. It's compounded by urban myths and legends and some good intentioned "delete the prefs" people without the time or perhaps the need to look into the problem.
Keep trying Steffen and I beleive you will be not only happy when you get it all working, and additionally you will make SOME of your workflow more efficient and become more knowledgeable in the process. Jan 24, AM. Warwick, you are very helpful.
I repeated the setup procedure again with no avail. Here are the error messages from slave's transcoderx. The last line in German means that the source file was not found. Jan 24, PM. Recall you have set automatic file sharing to OFF in the compressor qmaster cluster setup. This helps to get this working and understand what is going on here.
IF a no-route or similar, please set up your ethernet point to point. The file system should mount on your slave mac see the desktop. Do you get the same error for the 1.
You should NOT have to do this.. The Apple logo is a trademark of Apple Inc. Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors. Note: Because Apple frequently releases new versions and updates to its system software, applications, and Internet sites, images shown in this manual may be slightly different from what you see on your screen. AppleCare is a service mark of Apple Inc.
The YouTube logo is a trademark of Google Inc. Other company and product names mentioned herein are trademarks of their respective companies.
0コメント